Miele Tumble Dryers

When the PIN code function is activated, the dryer will display '###' flashing in the time display after being switched on. This means you need to enter the 000 PIN code to operate the dryer.

When the dryer is switched on, '000' appears on the display. This indicates that a PIN code access feature has been activated, requiring a code to operate the appliance.

The message 'Adjust the load' appears on the display, and the drying programme is cancelled. This occurs if the drum contains very little laundry or if the items are already sufficiently dry, causing the dryer to stop prematurely.

The tumble dryer automatically switches itself off once a drying program has completed. This is not a fault, but a standard energy-saving feature.

The tumble dryer will automatically switch itself off after 15 minutes if no program selections or other operations are made. This is a normal energy-saving feature.

This message ( Blockage detected. See ) appears after a program has been interrupted. It suggests that the laundry inside the drum is unevenly distributed or has rolled up into a ball, which can hinder proper drying.

The heat exchanger can become blocked, potentially leading to damage to the appliance. This is caused by a plinth filter that is either damaged or worn out.

The dryer is producing buzzing or humming sounds. This is not a fault, but the normal operating noise of the heat pump compressor (part of the heat pump system).

If the programme selector is moved after a drying programme has already started, the message 'Cannot be changed' will appear in the display. This is a safety feature to prevent unintentional alterations during an active drying cycle.

The dryer's display shows a reminder that the lint filter is clogged and needs immediate cleaning. This warning helps maintain dryer efficiency and safety.

This message ( Change not possible) appears when you attempt to select a different drying program after a current program has already begun. The dryer prevents unintentional program alterations during operation.

The message 'Clean out airways' is displayed on the screen. This indicates that there is a minor accumulation of fluff or debris in the dryer's airways, which needs to be cleaned to maintain optimal drying performance and efficiency.

This message ( Clean plinth filter. See ) appears at the end of a drying program, signaling that lint has accumulated in the dryer's airways, particularly around the plinth filter, which requires cleaning.

This critical message ( Clean plinth filter. See ) appears after a program has been interrupted, indicating an excessive and problematic amount of lint accumulation that requires immediate attention to the dryer's filter and air duct systems.

The dryer display shows 'Code 000' flashing or lit up immediately after being switched on. This indicates that a security access code has been enabled on the appliance, preventing immediate operation.

A continuous buzzer sounds from the dryer to indicate that a fault condition has been detected. This fault buzzer is distinct from the end-of-programme buzzer and operates regardless of the buzzer volume setting.

The dryer's display screen is dark, and the 'Start/Stop' button is slowly flashing. This indicates that the dryer is in its normal standby mode to conserve energy and is not a fault.

The dryer's display remains completely off, indicating that the appliance is not receiving electrical power. This prevents any operation of the dryer.

The interior light of the dryer drum does not illuminate. This is often not a fault but reflects normal operating conditions related to the door status.

The drum lighting automatically switches off when the door is closed or after a few minutes if the door is open, to save energy. It should come on when the dryer is switched on and the door is opened.

The interior drum light does not illuminate when expected. This is typically due to energy-saving features where the light switches off automatically when the door is closed, or after a few minutes if the door is left open.

The drum lighting does not illuminate. This can be due to energy-saving features (lighting goes out automatically) or, less commonly, a fault with the light itself.

During a longer Delay start time, the drum occasionally rotates. This is a normal function of the dryer and not a fault; it helps to untangle the laundry before the programme begins.

The dryer automatically switches off completely at the end of a programme. This is a normal energy-saving function and does not indicate a fault with the appliance.

This tumble dryer is designed to switch off automatically at the end of a programme. This is an integrated energy-saving feature to reduce power consumption. It is a normal function and does not indicate a fault with the appliance.

The tumble dryer switches off automatically after 15 minutes if no selections are made. This is a normal energy-saving function designed to conserve power when the appliance is idle.

The drying programme stops and displays a fault message. This typically occurs if the plinth filter was re-inserted into the dryer while still dripping wet after cleaning.

This message ( Empty container See ) appears after a program has been interrupted, indicating that the condensed water container is full or that the drain hose is kinked or blocked.

This message appears at the end of a drying program, indicating that the laundry is currently undergoing a cooling-down phase. This helps prevent creasing and makes the laundry easier to handle.

The display shows '  Service Fault F XXX' after a program has been interrupted. 'XXX' represents a specific three-digit fault code indicating an internal service fault.

A drying program is interrupted, and a general fault message appears on the display. This indicates that the plinth filter, after being cleaned, was reinserted while still too wet.

A fault message continues to appear after re-fitting the plinth filter, even if it was properly dried. This suggests that there are stubborn residues from washing substances trapped in the filter.

At the end of a programme, flashing bars on the display indicate that the drying cycle is complete, but the laundry inside the drum has not yet cooled down sufficiently.

Bars (e.g.,  ...  ...  ...) flash in the display at the end of a programme. This means the programme has finished, but the laundry inside has not yet cooled down completely.

The dryer produces a humming sound during its operation. This is a normal functional noise and does not indicate a fault. It can be heard when the compressor (heat pump) or the condensed water pump is working, or when the 'Steam smoothing' programme is active.

The language displayed on the dryer's screen is not the desired language, making it difficult to understand or operate the appliance.

The dryer is experiencing a lack of proper air flow and heat within the heat exchanger. This severe issue is often caused by a plinth filter that is either damaged or has not been cleaned sufficiently over time, leading to clogging.

The dryer is not effectively spraying water to remoisten laundry, which can impact the results of programmes that require moisture, like 'Steam smoothing'. This is typically caused by blockages in the condensed water system.

The Steam smoothing programme is not producing enough spray to remoisten the laundry effectively. This typically indicates a blockage or calcification issue within the dryer's water delivery system for the steam function.

The interior drum lighting automatically switches off when the door is closed or after a few minutes when the door is open. This is a normal energy-saving function, not a fault.

The dryer programme does not begin operation after it has been selected. This could be due to a lack of power, the door not being closed, or the dryer not being switched on.

The tumble dryer has stopped operating because the main electrical power supply was interrupted, for example, by a power cut. The dryer requires user interaction to resume its cycle once power is restored.

A selected drying program fails to begin, and there is no clear error message or indication on the display.

The message 'Programme cannot be changed' appears on the display when the programme selector is moved while a drying programme is already in progress. This feature prevents unintentional alterations to an active drying cycle.

The dryer does not respond when attempting to start a programme, indicating it may not be properly connected to power, switched on, or the door is not fully closed. There is no obvious cause displayed.

When you try to start a drying programme, the dryer does not begin its operation. This can be caused by various issues related to power supply, the appliance being switched off, or the door not being properly closed.

The tumble dryer is unresponsive and a drying programme won't begin. This can be due to power issues or the dryer not being ready to operate.

This message appears on the display when the programme selector knob has been moved from its original position while a programme is running or about to start. The dryer prevents program changes to avoid unintended operation.

A general service fault message 'Service Fault F' appears on the display after a programme has been cancelled, with no other obvious cause provided. This indicates an internal issue that may be transient.

When a programme is running, only the Start/Add laundry sensor control flashes slowly after about 10 minutes. This is a normal energy-saving function and not a fault, as other indicators go out.

After a programme has been running for 10 minutes, the control panel indicators go out, and only the Start/Add laundry sensor flashes slowly. This is a normal energy-saving function.

The dryer's display is dark, and the Start/Stop button is blinking slowly. This indicates the appliance has entered energy-saving Standby mode. The drum may still turn at intervals during the anti-crease phase.

The display is dark and the 'Start/Stop' button flashes slowly. This is a normal standby function designed to save energy and does not indicate a fault. The drum may still turn at intervals if the anti-crease phase is active.

Approximately 10 minutes after the drying programme has finished (or 15 minutes after the anti-crease phase concludes), the 'Start/Stop' button will begin to flash slowly, and the display will go out. This is a normal energy-saving feature.

Approximately 10 minutes after a programme finishes, the Start/Stop sensor control will begin to flash slowly, and other indicators will dim or go out. This is a normal energy-saving feature and not a fault. The drum may also turn intermittently during the Anti-crease phase.

Approximately 10 minutes after a programme ends, the Start/Stop sensor begins to flash and the display goes out. This is a normal energy-saving function, not an error. The drum may also turn at intervals during the anti-crease phase.

The display shows 'Technical fault F' and the current drying programme is cancelled. This indicates a general internal technical problem with the appliance that requires attention.

The tumble dryer's Wi-Fi connection may experience sporadic or complete failures. This can happen because the Wi-Fi frequency range is shared with other household appliances, potentially causing interference.

The drying program has stopped due to a power interruption. The dryer is indicating that it lost power during operation but can potentially resume.

The dryer's card reader has detected an issue with the inserted card. This usually means the card is not seated properly or is not being read correctly.

An error has occurred in a program or language setting. The affected program or language will be marked with a '§' symbol and cannot be selected. This indicates a defect in the language data.

The drive motor is experiencing excessively high power. This can indicate the motor is working too hard or overheating. The program is paused.

The fan motor's temperature has become too high, causing the program to stop for safety. The dryer indicates a fan fault to prevent damage.

A fault has been detected in the gas system, which is essential for heating the dryer. This can happen at the start or during a program run.

A fault has been detected in the heating system, causing the program to stop. You can choose to continue the program, but it will run without any heat.

A persistent fault in the heating system has occurred, which cannot be bypassed by simply continuing the program. This type of heating fault requires professional intervention.

A general machine fault has occurred. The dryer indicates an internal issue that may require professional attention if a simple restart doesn't clear it.

A fault has been detected in the pressure sensor. This sensor is crucial for various dryer functions, and a persistent error means the dryer cannot operate correctly.

A general system fault has occurred, which the dryer could not resolve. This message appears if other error messages cannot be fixed after five restarts.

The message 'Clean out airways' lights up on the display at the end of a drying programme. This indicates that there is a significant build-up of fluff within the dryer's airways, which can impede performance and efficiency.

At the end of a drying program, the fluff filter symbol illuminates. This means there is a build-up of fluff in the airways that needs to be cleaned.

This indicator light signals that the tumble dryer is not operating correctly or economically, often due to blockages from fluff or detergent residues.

The  indicator light comes on at the end of the programme. This suggests the tumble dryer is not working correctly or economically, often due to clogging from fluff or detergent residue.

These indicators, accompanied by a signal tone after a cancelled programme, mean the dryer's system is clogged by fluff or detergent residues, impacting its performance.

If the , , and  indicators continue to flash after thorough cleaning and a programme is terminated again, it suggests a deeper clog in the system or an issue with the heat exchanger.

When the display shows , it indicates that the programme selector knob has been moved from its original setting either after a programme started or while it was running. This prevents unintentional programme alterations and requires you to re-select the original programme.

When the display shows  flashing immediately after the tumble dryer is switched on, it means that the PIN code access feature is active. The dryer cannot be operated until the correct PIN code is entered, which prevents unauthorized use.

The display shows  because the programme selector knob has been moved from its original position during operation or standby.

The display shows '' because the program selector knob was accidentally moved from its original position while a program was running.

This display message, accompanied by an audible signal and programme cancellation, signifies that the laundry inside the drum is not evenly distributed or has rolled together into a ball. This can prevent proper drying and cause an imbalance within the drum.

The display shows  :  and the programme has been cancelled, accompanied by a signal. This means the laundry inside the drum is unevenly distributed or has rolled up into a ball.

After switching on the dryer, the  symbol lights up, indicating that a PIN code is required to access the appliance. This is a security feature to prevent unauthorized use.

After cancelling a programme, the tumble dryer enters a cooling-down phase. If the Start/Stop sensor control is pressed again during this cooling phase,  will light up. This indicates that the cooling process has been interrupted or acknowledged.

The display shows  and the buzzer sounds, indicating that the drying programme has successfully completed. The Start/Add laundry sensor will go out.

The display shows . This is an informational message, not a fault. It indicates that the tumble dryer is successfully connected to your home network.

The display shows . This is an informational message, not a fault. It indicates that the tumble dryer is connected to the SmartGrid system, allowing for intelligent energy management.

The  symbol and another number combination flash on the display after a programme cancellation, along with a signal. This indicates an internal fault for which no obvious user-remediable cause is apparent.

When the display shows '' along with a flashing number combination and an audible signal, it indicates an unspecified internal fault that has caused the programme to terminate. This suggests a temporary internal issue that may be resolved by a power cycle.

This fault message, accompanied by an audible signal after a programme has been cancelled, indicates a significant blockage within the dryer. Both the fluff filters and the plinth filter are likely clogged, and the internal airways underneath the plinth filter and the heat exchanger are also blocked with fluff.

The display shows . This is an informational message, not a fault. It indicates that the remote control function for the dryer is currently switched off in the settings.

The display shows  and programme start is not possible. This indicates that a software update is available for the tumble dryer, and the update process needs attention.

When you switch on the dryer, flashing lines (  ) appear, and you cannot select a programme. This indicates that a PIN code function has been activated, restricting access.

After the dryer is switched on, '' flashes in the time display and a program cannot be selected. This means the lock code function is activated, preventing the dryer from being used without authorization.

This message appears on the display when a programme is cancelled because the drum was either underloaded or the laundry items were already dry. This is a normal operation, not a fault with the appliance.

The display shows . This indicates that the tumble dryer is not currently connected to the network. This is an informational status, not necessarily a fault.

After a program is cancelled, the water container symbol lights up and an audible signal sounds. This indicates that the condensed water container is full or there is an issue with the drain hose.

If this indicator light comes on and an audible signal sounds after a programme has been cancelled, it signifies an issue with the drain hose. A kink in the hose prevents proper water drainage, leading to the fault.

The dryer's  indicator light comes on after a programme is cancelled, accompanied by an audible signal. This indicates that the condensed water container is full or there is a problem with the drain hose.

When the  indicator light comes on with a signal tone after a programme cancellation, it typically means the condensed water container is full or there's a blockage/kink in the drain hose.